​Welcome to ANDA

How to Customize a UPVC Profile Extrusion Line from a Cross-Section Drawing

Views: 4 Author: Site Editor Publish Time: Origin: Site

A cross-section drawing is a complete order. Wall thickness, chamber, chamber depth, cavity count and overall width tell you which extruder to pair, which die to machine, and how hard the calibration and haul-off stages must work. A customized UPVC profile line is specified from that drawing, not from a generic machine catalog.

Anda's UPVC profile production line is built around the drawing: a conical twin screw extruder matched to the profile's maximum width, a vacuum calibration table sized to the cavity count, and downstream units - haul-off, cutter and stacker - synchronized to the line speed the profile needs. Here is how a cross-section drawing turns into a running line.

What the Cross-Section Drawing Decides

The drawing sets four things before any machine is selected. Maximum width chooses the extruder class: a narrow window profile runs on a smaller screw, while a deep door frame or a wide multi-chamber profile moves up the range. Wall thickness and chamber depth set the melt pressure the die must handle, and the cavity count decides how much calibration surface and how many cooling zones the table needs.

Send the drawing as CAD or a measured cross-section, plus the target meters per minute. The line is then specified cavity by cavity, so the dimensions you draw are the dimensions the line is built to hold. The current machine range is listed on the Anda UPVC profile making machine product page.

Matching the Extruder to the Profile

The line uses a conical twin screw extruder designed for PVC and UPVC powder. The screw plasticizes the compound at low temperature with a low shear rate, which keeps the surface of the finished profile smooth and free of bubbles - the two defects that show up first on thin-wall window profiles.

The model follows the maximum width of the drawing. The range steps from 180 mm through 240 and 300 mm up to 600 mm, with the extruder moving from a 55/110 on the narrowest line to an 80/156 on the wide door-frame lines. A commonly specified 65/132 extruder holds line speeds above 2 m/min on standard door and window profiles.

The line is equipped with energy-saving motors, which cut overall energy use by up to 20% or more. On a profile plant that runs the extruder around the clock, that is the largest controllable cost on the floor. Footage of the line running is in this video of the line running.

UPVC profile extrusion line conical twin screw extruder.png

The Vacuum Calibration Table Holds the Dimensions

Calibration is where a complex profile keeps its shape. The vacuum calibration table pulls the still-soft profile against a precision die and cools it in one held position, so every cavity takes the same dimension on every meter of output.

The table pairs a high-efficiency vacuum pump with full-system water temperature control and rapid cooling. That combination is what lets the line hold dimensional consistency at high speed, and it is the standard answer to the two problems that make shaped profiles difficult: deformation and twist in deep chambers and thin fins.

Haul-Off, Cutting and Stacking

The haul-off grips the profile with alloy rubber pads, so it pulls at a steady speed without marking the surface. The cutter runs high-hardness blades with pneumatic control and an automatic dust-collection unit, giving clean, burr-free cuts and keeping the area around the saw clear.

The stacker takes the cut lengths in order, which matters on door and window lines where profiles are cut to order length and sorted by cavity before packing.

UPVC profile production line haul off machine.png

One Line, Many Profiles

Customization does not stop at one profile. Changing the die moves the same line from casement and sliding window profiles to wall panels, window sill boards, louver blinds, cable ducts, skirting and protection corner. Changing the screw and barrel extends the line into PVC-based WPC products such as WPC wall panels and WPC window profiles, so the plant follows its orders instead of the machine's limits.

On window and door profile lines the line can also run online sealing strip co-extrusion with an online sealing strip installation unit, which puts the seal on during extrusion instead of in a separate assembly step. The broader profile machine options are compared in this article on finding a reliable PVC profile machine manufacturer.

Sizing the Line

The four standard configurations cover most door and window drawings. Match the maximum width of your drawing to the line, then confirm the motor and line speed against your daily meter target:

Model

YF180

YF240

YF300

YF600

Extruder

55/110

65/132

80/156

80/156

Max applicable width

180 mm

240 mm

300 mm

600 mm

Motor power

22 kW

37 kW

55 kW

55 kW

Electricals across the range use ABB inverters, Schneider contactors and Omron temperature controllers, and the minimum total line consumption is 25 kWh at the smallest configuration.

UPVC profile production line automatic stacker.png

Conclusion

A cross-section drawing becomes a UPVC profile line in four steps: size the extruder to the maximum width, match the die and calibration table to the cavities, synchronize haul-off, cutting and stacking to the line speed, and leave room to change dies as the order book grows. For your drawing, quotes and installation details, the Anda contact page answers within one business day.

About Zhangjiagang Anda Machinery Co., Ltd.

Zhangjiagang Anda Machinery Co., Ltd. manufactures UPVC profile production lines and other plastic extrusion lines, with pre-sales consultation and after-sales installation service from its service center in India, as a one-stop solution for UPVC profile extrusion equipment. The current range of lines is listed on the Anda Machinery website.

Frequently Asked Questions

Q: What do I need to send to get a customized line?

Send the cross-section drawing, the maximum profile width, the target line speed in meters per minute and the local voltage standard. The line is then specified from those four points: extruder class, die, calibration table and downstream units.

Q: Can the same line produce more than one profile?

Yes. Changing the die moves the line between window and door profiles, wall panels, window sill boards, louver blinds, cable ducts, skirting and protection corner. Changing the screw and barrel extends it to PVC-based WPC products.

Q: How does the line keep thin-wall dimensions stable at high speed?

The vacuum calibration table pairs a high-efficiency vacuum pump with full-system water temperature control and rapid cooling, holding every cavity in one cooled position. That is the standard setup for deep-chamber and thin-fin profiles.

Q: Does the line include sealing strip co-extrusion?

Window and door profile lines can be equipped with online sealing strip co-extrusion and an online sealing strip installation unit, so the seal is applied during extrusion rather than in a later assembly step.